Emergency Ac Repair
If your cooling fails before a planned replacement, emergency repair can bridge the gap until the new system is installed.
System design and installation
A new HVAC system for your Severance, CO home, sized by calculation and proven at startup
The quality of an installation decides how a system performs for the next fifteen years. We calculate the load, evaluate the ducts, install to the manufacturer's specifications and verify the results with measurements before we call the job done.
Installation checklist
- Load calculation
room by room, never rule of thumb - Duct review
static pressure measured before quoting - Commissioning
charge, airflow and safety verified
Established 2011Installing systems across Severance, CO for years
Permits handledWe pull permits and schedule the inspection
Protected job sitesFloors covered and old equipment hauled away
Registered warrantiesManufacturer registration completed for you
About our installation team
Installation is a design job first and a construction job second
The equipment in the box is only as good as the decisions made before it is unpacked.
Walk into any supply house and you will find furnaces, air conditioners and heat pumps with impressive efficiency ratings printed on the side. Those numbers are measured in a laboratory under ideal conditions. In a real Severance, CO home, the performance you actually receive depends on whether the equipment is the right size, whether the ductwork can move the air it needs, whether the refrigerant charge is correct and whether the controls are set up for the way you live. Those are installation questions, and they are where we put most of our effort.
We have been designing and installing heating and cooling systems in this area since 2011. Over those years we have replaced plenty of equipment that was installed too large, connected to ducts that could not carry its airflow or charged by guesswork. Oversized equipment short cycles, wears out early and leaves rooms clammy. Undersized ducts make blowers loud and coils ice over. None of those problems show up on the spec sheet, but all of them show up on the utility bill and in your comfort.
Starting with the house, not the box
Every replacement or new installation begins with a site survey and a load calculation. We measure rooms, note window sizes and orientation, check insulation levels where we can see them and account for how the home is built. That calculation tells us how much heating and cooling each room actually needs. We then look at the existing ductwork, measure static pressure on the current system and inspect returns and supplies for size and condition. Only after that do we talk about equipment.
Choosing equipment with you
Most homes have more than one reasonable path. A high-efficiency furnace paired with a new air conditioner may make sense for one family, while a cold-climate heat pump with a gas furnace as backup suits another. We explain the differences in comfort, operating cost, maintenance and expected lifespan, and we give you written prices for each option so the comparison is fair.
Installed to the book, verified by measurement
On installation day, our crew protects floors and finishes, removes the old equipment and installs the new system following the manufacturer's instructions for clearances, venting, drainage and electrical connections. Refrigerant lines are brazed with nitrogen flowing to prevent internal scale, pressure tested and evacuated with a micron gauge before the refrigerant is released. Then comes commissioning: we measure airflow, temperature rise or split, refrigerant charge, gas pressure and combustion values, and we record them on a startup sheet that stays with your system records.
After the crew leaves
We walk you through the thermostat, filter changes and anything else you need to know, register the equipment with the manufacturer when that applies, and schedule the permit inspection. If something does not feel right in the first weeks, one call brings back the same team that did the work.
Why we avoid rushed quotes
A price written from the driveway after a five-minute look is easy to give and hard to trust. It usually means someone copied the size of the old unit and added a margin. Our proposals take longer because they rest on measurements, and each one lists the equipment model numbers, the scope of duct and electrical work, the permit and the commissioning steps included. When you compare our proposal with others, you will know exactly what is being offered, which makes the comparison honest for everyone.
2011the year we began installing systems in Severance, CO
Manual Jthe load method behind every system we quote
One crewfrom site survey through final startup
Our services
Services for every stage of a system's life
Installation is our focus on this page, but a system needs care long after startup day. The same technicians who design and install equipment also repair it, maintain it and handle the plumbing that shares the mechanical room with it.
Browse by category. Every service page explains what the work involves, what affects the scope and what questions Severance, CO homeowners ask most often.
Air conditioning systems
From a like-for-like condenser swap to adding central air to an older home.
#link-ac-installation#
Condenser and coil replacements matched as a system, with new line sets or proper flushing, nitrogen brazing and a deep evacuation.
Central Air Installation
Whole-home cooling added to houses with radiators, baseboard or no ducts at all, planned around attic, closet and chase space.
#link-ac-compressor-repair#
Before replacing a whole system for a compressor failure, we compare the repair against new equipment so the choice is informed.
#link-ac-tune-up#
The first tune-up after installation confirms the commissioning numbers still hold once the system has run through a full season.
Heating equipment
Furnaces, boilers and heat pumps selected for local winters and installed to specification.
Boiler Repair
Service for existing hot water and steam boilers, including the controls and pumps we tie into when zoning is added.
Boiler Replacement
Condensing and conventional boilers installed with primary-secondary piping, air separation and dirt removal to protect the new heat exchanger.
Furnace Replacement
Gas and electric furnaces installed with correct venting, gas piping, condensate drainage and a measured temperature rise at startup.
Heat Pump Repair
Support for existing heat pumps, including the defrost and auxiliary heat settings that are often misconfigured at installation.
Heat Pump Installation
Ducted and ductless heat pumps sized for heating load, mounted clear of snow and drainage, and set up with proper backup heat staging.
Ducts, ventilation and controls
The distribution side of the system, where comfort is won or lost.
Indoor Air Quality Testing
Testing before an installation shows whether filtration, ventilation or humidity equipment belongs in the new system design.
#link-air-cleaning-and-humidifiers#
Media filters, whole-house humidifiers and dehumidifiers integrated into the new air handler with proper drainage and controls.
Ductwork Install And Replace
Supply and return systems designed from room loads, with duct sizes chosen to keep static pressure inside the equipment's rated range.
Duct Sealing
Sealing existing duct joints and seams at installation time is often the cheapest efficiency gain available in the whole project.
Dryer Vent Cleaning
Dryer vent runs rerouted or shortened when a remodel or new mechanical layout changes where the laundry connects.
Thermostat Repair And Replacement
Thermostats configured for the equipment stages, heat pump logic and accessories the new system actually has.
Water and drain systems
Plumbing services that live alongside your heating equipment.
Backflow Testing
New boiler feeds and irrigation connections often need a backflow assembly tested before the water provider considers it in service.
Drain Cleaning
Clearing floor drains and condensate paths near the mechanical room so new equipment has a reliable place to drain.
Water Heater Repair
Repairs for existing tanks and tankless units, and honest guidance when replacement alongside a new heating system makes sense.
Bathroom Plumbing Repair
Fixture and valve repairs handled by the same team, so a remodel or system upgrade does not need a second contractor.
Frozen Pipe Repair
Supply lines relocated or insulated when a new system layout or renovation exposes pipes to unheated spaces.
Commercial projects
Mechanical and plumbing work for owners, managers and general contractors.
Hvac Contractor
Rooftop unit changeouts, tenant build-outs and mechanical scopes for commercial buildings, with permits and closeout documents.
Commercial Drain Cleaning
Drain line preparation and jetting for commercial spaces being renovated or brought back into service.
Commercial Plumbing Repair
Water heaters, mixing valves and restroom fixtures for businesses, installed and repaired with commercial-grade components.
Thinking about a new system but not ready to decide?
Replacing heating or cooling equipment is one of the larger investments most homeowners make, and it deserves more thought than a rushed decision on a hot afternoon. If your system is aging but still running, the best time to plan is now, while you have the luxury of comparing options, checking your ductwork and choosing a convenient installation date.
Signs that planning makes sense include repair bills that are becoming a regular event, rooms that never reach the thermostat setting, humidity that feels wrong in summer and equipment that relies on refrigerant no longer produced. A consultation costs you a little time and gives you a clear picture of what the home needs, what the options cost and how long your current equipment is likely to last.
Remodels and additions are another natural moment to revisit the mechanical system. Finishing a basement, adding a bedroom over the garage or opening up a floor plan changes the heating and cooling load, and the existing equipment and ducts may no longer match the house. Bringing us in during the design stage, rather than after the drywall is up, gives far better results and usually costs less. The same applies to Severance, CO homeowners replacing windows or adding insulation, since both reduce the load and can allow smaller, quieter equipment.
How it works
Our eight-step installation process
The same sequence runs on every job, whether it is a single furnace swap or a complete system with new ductwork and zoning. Following it every time is what keeps the results consistent from one home to the next, and it means you always know which stage your project has reached and what comes after it.
Consultation
We talk through comfort complaints, rooms that never feel right, utility costs and your plans for the home before looking at equipment.
Site survey
Rooms are measured, windows and insulation noted, and the existing equipment, ducts, venting and electrical service inspected.
Load calculation
A room-by-room heating and cooling load tells us what capacity the home needs and how much air each room should receive.
Written options
You receive equipment options with prices, efficiency, comfort features and expected upkeep, written so they compare fairly.
Permits and scheduling
We file the required permits, order equipment and schedule installation around your calendar.
Installation day
Floors are protected, old equipment removed and the new system installed to the manufacturer's specifications.
Commissioning
Airflow, charge, gas pressure, combustion and safety controls are measured and recorded on a startup sheet.
Walkthrough and inspection
We show you how to operate the system, register warranties where applicable and meet the inspector to close the permit.
Commissioning is the step most often skipped in the industry and the one that matters most to long-term performance. A system that is charged by feel or started without airflow measurements may seem fine on the first day, but small errors add up to higher bills, noisy operation and shortened equipment life. Recording the startup values also gives every future technician a reference point, so a change in performance years later can be spotted and explained quickly.
From our customers
Homeowners describe their new systems
Notes from households who replaced aging equipment or added a system for the first time with our installation team, describing the planning, the installation day and how the home feels now.
We expected the salesperson to push the biggest unit. Instead, the estimator measured every room and told us our old system had been oversized. The new heat pump is smaller, quieter and the house finally holds an even temperature upstairs and down.
Natalie K.Homeowner, Severance, CO
The crew covered every floor from the door to the basement, and the old furnace was gone before lunch. They gave us a sheet with all the startup readings.
Robert A.Homeowner, Severance, CO
Adding central air to our older house worried us. They found a route for the ducts through two closets that we never would have thought of.
Joanna P.Homeowner, Severance, CO
They handled the permit and came back for the inspection, which passed the first time. Nothing for us to chase.
Devon H.Homeowner, Severance, CO
Our boiler replacement included cleaning out the old piping. The installer explained why that protects the new boiler.
Samira N.Homeowner, Severance, CO
Installation questions
Planning a new system: what homeowners ask us
Answers to the questions that come up during almost every installation consultation.
How long does a typical full system replacement take?
A straightforward furnace and air conditioner replacement usually takes one day. Projects with new ductwork, added zones or a first-time central air installation can take several days, and we give you the schedule in writing beforehand.
Is it better to replace the furnace and air conditioner together?
Replacing both at once lets us match the indoor coil, blower and outdoor unit so the system performs as rated, and it avoids two disruptions. If one unit is fairly new, replacing only the other can still make sense, and we will explain the tradeoffs.
How do you decide what size system my home needs?
We perform a load calculation using room dimensions, windows, insulation, orientation and construction details. The old equipment's size is only a reference, because many existing systems were oversized.
Can my existing ductwork be reused with new equipment?
Often, yes. We measure static pressure and inspect the ducts first. If they are undersized, leaky or damaged, we recommend targeted modifications so the new equipment can deliver its rated airflow.
Who is responsible for the permit and final inspection?
We are. We file the permit, schedule the inspection and meet the inspector, so you do not have to coordinate it yourself.
What happens to the old equipment you remove?
We haul it away. Refrigerant is recovered by certified technicians before the old unit leaves your property, as federal rules require.
How does a heat pump compare with a furnace and air conditioner?
A heat pump heats and cools with one outdoor unit by moving heat rather than burning fuel. Cold-climate models perform well in winter, and many homes pair one with a furnace for the coldest days. We compare operating costs for your home during the consultation.
What upkeep does new equipment need to protect its warranty?
Manufacturers generally expect regular filter changes and periodic professional maintenance. Keeping records of service visits helps if a warranty claim is ever needed.
Can you install a system that runs quietly?
Yes. Variable-speed blowers, two-stage or inverter compressors, correct duct sizing and careful placement of the outdoor unit all reduce noise. Undersized ducts are the most common cause of loud airflow, so we address them during design.
Is a ductless system a good option for my home?
Ductless heat pumps work well for additions, converted spaces, older homes without ducts and rooms that the main system struggles to reach. We compare ducted and ductless approaches during the consultation.
Start planning your new system
Call to book an installation consultation. We will survey the home, calculate the load, review the ductwork and give you written options you can compare at your own pace, without pressure to sign on the spot.
Every installation includes
- A room-by-room load calculation before any equipment is recommended.
- Duct evaluation with static pressure measured on your current system.
- Permits, inspection scheduling and removal of old equipment.
- Commissioning with recorded readings you keep for your records.
- A walkthrough of the new controls, filter schedule and warranty paperwork before the crew leaves your home.